<TABLE height=25 cellSpacing=0 cellPadding=0 width=515 border=0>
<TR>
<TD class=infobt vAlign=bottom align=middle>模具英语专业术语</TD></TR></TABLE>
<TABLE height=16 cellSpacing=2 cellPadding=2 width=515 border=0>
<TR>
<TD vAlign=top align=middle></TD></TR></TABLE>
<TABLE height=25 cellSpacing=2 cellPadding=2 width=515 border=0>
<TR>
<TD class=infokc vAlign=top> <BR>模具述语 <BR>一、入水：gate <BR>进入位： gate location <BR>水口形式：gate type <BR>大水口：edge gate <BR>细水口： pin-point gate <BR>水口大小：gate size <BR>转水口： switching runner/gate <BR>唧嘴口径： sprue diameter <BR>二、流道: runner <BR>热流道： hot runner,hot manifold <BR>热嘴冷流道: hot sprue/cold runner <BR>唧嘴直流: direct sprue gate <BR>圆形流道：round(full/half runner <BR>流道电脑分析：mold flow analysis <BR>流道平衡:runner balance <BR>热嘴： hot sprue <BR>热流道板：hot manifold <BR>发热管：cartridge heater <BR>探针: thermocouples <BR>插头： connector plug <BR>插座： connector socket <BR>密封/封料： seal <BR>三、运水：water line <BR>喉塞：line lpug <BR>喉管：tube <BR>塑胶管：plastic tube <BR>快速接头：jiffy quick connector plug/socker <BR>四、模具零件： mold components <BR>三板模：3-plate mold <BR>二板模：2-plate mold <BR>边钉/导边：leader pin/guide pin <BR>边司/导套：bushing/guide bushing <BR>中托司：shoulder guide bushing <BR>中托边L：guide pin <BR>顶针板：ejector retainner plate <BR>托板： support plate <BR>螺丝： screw <BR>管钉：dowel pin <BR>开模槽：ply bar scot <BR>内模管位：core/cavity inter-lock <BR>顶针： ejector pin <BR>司筒：ejector sleeve <BR>司筒针：ejector pin <BR>推板：stripper plate <BR>缩呵：movable core,return core core puller <BR>扣机（尼龙拉勾）：nylon latch lock <BR>斜顶：lifter <BR>模胚（架）： mold base <BR>上内模：cavity insert <BR>下内模：core insert <BR>行位（滑块）： slide <BR>镶件：insert <BR>压座/斜鸡：wedge <BR>耐磨板/油板：wedge wear plate <BR>压条：plate <BR>撑头: support pillar <BR>唧嘴： sprue bushing <BR>挡板：stop plate <BR>定位圈：locating ring <BR>锁扣：latch <BR>扣鸡：parting lock set <BR>推杆：push bar <BR>栓打螺丝：S.H.S.B <BR>顶板：eracuretun <BR>活动臂：lever arm <BR>分流锥：spure sperader <BR>水口司:bush <BR>垃圾钉：stop pin <BR>隔片：buffle <BR>弹弓柱：spring rod <BR>弹弓:die spring <BR>中托司：ejector guide bush <BR>中托边：ejector guide pin <BR>镶针：pin <BR>销子：dowel pin <BR>波子弹弓：ball catch <BR>喉塞: pipe plug <BR>锁模块：lock plate <BR>斜顶：angle from pin <BR>斜顶杆：angle ejector rod <BR>尼龙拉勾：parting locks <BR>活动臂：lever arm <BR>复位键、提前回杆：early return bar <BR>气阀：valves <BR>斜导边：angle pin <BR>术语：terms <BR>承压平面平衡：parting surface support balance <BR>模排气：parting line venting <BR>回针碰料位：return pin and cavity interference <BR>模总高超出啤机规格：mold base shut hight <BR>顶针碰运水：water line interferes withejector pin <BR>料位出上/下模：part from cavith (core) side <BR>模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. <BR>不准用镶件： Do not use (core/cavity) insert <BR>用铍铜做镶件： use beryllium copper insert <BR>初步（正式）模图设计：preliinary (final) mold design <BR>反呵：reverse core <BR>弹弓压缩量：spring compressed length <BR>稳定性好：good stability,stable <BR>强度不够：insufficient rigidity <BR>均匀冷却：even cooling <BR>扣模：sticking <BR>热膨胀：thero expansion <BR>公差：tolorance <BR>铜公(电极）：copper electrode </TD></TR></TABLE> |
|小黑屋|手机版|模具论坛
( 浙ICP备15037217号 )
发表于 2005-5-11 16:26:00
楼主
/5 
