用实体设计做个杯子，为什么不能完成抽壳。

haubest

[此贴子已经被作者于2003-5-7 7:33:19编辑过]

sdh

我以前做过，能抽壳。用布尔运算合成一个零件试试！

haubest

终于完成了，先抽壳，再做把儿。

lqy821821

楼上：杯子如何造型最简单？

haubest

把和咀我都是扫描的

chendz

把儿用扫描好作；嘴用扫描如何作，用放样是否简单些。

lqy821821

两位能否详细点？

haubest

杯子半径60,高度210.扫描轨迹下端点离底面80,离杯子中心线50.

lqy821821

楼上：方法不错！简便易行！

computer

我怎么不会呀。

lqy821821

杯子！<img src="attachments/dvbbs/200352513441431192.gif" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/200352513441431192.gif\');}" onmousewheel="return imgzoom(this);" alt="" />

lqy821821

关键是先做好杯体和嘴后进行抽壳，再做把！

lqy821821

采用先过渡把和杯体的方法，可以先将把做好再同时进行抽壳！<img src="attachments/dvbbs/200352514381271286.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/200352514381271286.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

lqy821821

<img src="attachments/dvbbs/200352514481417979.gif" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/200352514481417979.gif\');}" onmousewheel="return imgzoom(this);" alt="" />

hmhmzzm

我也回去试试！我需要学习！

cqwq22

不能抽壳的原因是：由于你做的把较细，在抽壳的时候出现运算错误，解决的办法有两种，1.先抽壳在做把。2.将把做大一些，壳薄一些。这是你会看见，把中间也是空的了。

hmhmzzm

这是我做的杯子。嘴是放样作的，把是扫描完成的。<img src="attachments/dvbbs/20037219194340791.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20037219194340791.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

weiyi

以下是引用lqy821821在2003-5-25 13:46:25的发言：
关键是先做好杯体和嘴后进行抽壳，再做把！

我有个办法，可以做好把后，再抽壳。但我目前没有软件试，各位可以做做看。
依次做好杯体、嘴、把后，将把暂时隐藏（压缩），然后抽壳，完成。如果抽壳失败，暂时不理会，将把的生成顺序在设计树调整到最后，应该就可以了。
如果有哪位做成，请告诉我。

王建新

<img src="attachments/dvbbs/20037212072028440.gif" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20037212072028440.gif\');}" onmousewheel="return imgzoom(this);" alt="" />
请指教

hmhmzzm

做的不错！请问这种gif图片是怎么作成的？还请赐教！