跪求：连接器精密模具方面资料

lhxymxc

因为面试公司是做电脑连接器的，所以想了解，以便能录取！！！！

幻梦

心有同感，我现在也跟你一样!![em06]

压铸模撑门

？？？？非解？？？？

190281917

<p><strong>连接器精密模具方面资料？？？？没有这处必要吧！你只要懂的注模的结构，知识就可以了！连接器精密模具没有什么特别的地方。你就大胆的去面试吧！本人以前就是搞连接器精密模具的。</strong></p>

vanceden

<p>我现在就是做連接器的，最好不要入这行，因为工资好低。我做一个课长才3k多....</p>

szkxmf

<p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: &quot;Times New Roman&quot;; mso-hansi-font-family: &quot;Times New Roman&quot;; mso-bidi-font-family: &quot;Times New Roman&quot;; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　呵呵，不用跪求啦，跟我学几天保你应聘成功：）</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　　我做了近二十年的连接器精密塑模，这种模具产量高，一般模具寿命要求在</span><span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: &quot;Times New Roman&quot;; mso-bidi-font-size: 12.0pt; mso-fareast-font-family: 宋体; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">100</span><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">万次以上，尺寸精度要求高，所以设计时就要考虑到以后的修模要方便，大多做成镶拼式，注意冷却水管要足够，排气、累积公差等。。。</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　</span></p>

martin-sky

第 <font color="red">6</font> 楼讲的不错!

qixilove

說得這麼輕松啊，真正的連接器還是很難開的，就0.3的fpc和0.4的bob有人開出來嗎，能教點經驗嗎，現在80pin的fpc真是搞不定了，總是黏母模啊，變行又難搞啊

ccccjjj

精密模具。关键要点还是加工上的问题。跟设计没多大的关联。<br/>当然了。做个这一类的模具设计起来就是驾轻就熟了。别怕。[em01][em01]

嘿咻哥哥

<div class="msgheader">QUOTE:</div><div class="msgborder"><b>以下是引用<i>szkxmf</i>在2006-12-4 21:28:00的发言：</b><br/><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　呵呵，不用跪求啦，跟我学几天保你应聘成功：）</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　　我做了近二十年的连接器精密塑模，这种模具产量高，一般模具寿命要求在</span><span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA; mso-fareast-font-family: 宋体;">100</span><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">万次以上，尺寸精度要求高，所以设计时就要考虑到以后的修模要方便，大多做成镶拼式，注意冷却水管要足够，排气、累积公差等。。。</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　</span></p><p><span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-bidi-font-size: 12.0pt; mso-ascii-font-family: 'Times New Roman'; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">　　</span></p></div><p></p>姐姐说的很有道理啊 有空教教我啊[em02][em07]

walter006

[em03]

Andiwu

0.4btb算個屁屁啊，有種來我公司試試！

向延平

接插件这行还是可以的,年薪拿20万的人多的不的了

独孤婆婆

<div class="msgheader">QUOTE:</div><div class="msgborder"><b>以下是引用<i>Andiwu</i>在2007-7-17 13:30:00的发言：</b><br/>0.4btb算個屁屁啊，有種來我公司試試！</div><p></p>你们公司最小做到多少啊。我们最小做到0.17[em04]

zhouxingjiang99

[em31]

ninja37

:) :) :)

热血男儿

还是14楼的牛

fjmabamaba

长见识 做这个不能急

伟生1979

0.3的FPC我们现在都搞不定了,80PIN以上的变形太大,50PIN 就有10几条的变形了

lss2005

连接器精密模具很枯燥的哦