这样的内空件，实体设计怎样通过抽壳做出来？

haubest

如图。（我不是通过抽壳做出来的，记得SW可以直接做出）<img src="attachments/dvbbs/20039614105910716.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039614105910716.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

azhang

不是直接好抽的啊，看看我抽完后的剖开图

<img src="attachments/dvbbs/2003971053761624.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/2003971053761624.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

haubest

是直接抽的吗？怎么抽的?

cqwq22

感觉是抽壳后再加一个平板盖好些。

azhang

一个长方体加一个园柱体，再点右键抽壳

hmhmzzm

以下是引用azhang在2003-9-8 12:05:47的发言：
一个长方体加一个园柱体，再点右键抽壳

我记得这样可以实现抽壳的。

haubest

如像楼上说的那么简单，我就不用问了。我想一次就抽出内空，像SW一样。

hmhmzzm

回去一定试试，呵呵，没有调查就没有发言权！

xiujma

可以一步抽成
<img src="attachments/dvbbs/20039814112212260.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039814112212260.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

xiujma

这样作出来<img src="attachments/dvbbs/20039814165594889.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039814165594889.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

haubest

原来不指定抽壳面也可抽壳，谢谢。我以为必须指定一个面，所以无论怎么抽都抽不成，看来实体设计还有许多技巧没有掌握。

顺便再问一个问题，实体设计能否进行不等厚度的抽壳。

[此贴子已经被作者于2003-9-8 20:09:47编辑过]

xiujma

实体设计好象不行，但是制造工程师XPR2可以做到。

haubest

楼上指的是不能抽不等厚度的壳吗？

xiujma

界面如下：
<img src="attachments/dvbbs/20039109412548357.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039109412548357.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

xiujma

结果如下:
<img src="attachments/dvbbs/20039109424688819.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039109424688819.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

computer

好，又学了一手。

dhhzk123

xp00

xp00