UG有限元解算后看不到分析结果

jxthyunfeng

请教各位：我在用UG做有限元分析，到解算完成后，却进入不了后处理看到分析结果。以前可以的，不知道是不是装了ansys之后就出了问题。哪位知道解释一下。谢谢了。

jxthyunfeng

============================================================
列出信息创建者：     gyf
日期                           ： 2009-4-17 12:52:12
当前工作部件              ： E:\ug\12_sim1.sim
节点名                      ： rd-gyf
============================================================

------------------------------------------------------------

解法综合检查错误汇总

------------------------------------------------------------

解算器是 NX NASTRAN DESIGN

环境： NX NASTRAN DESIGN - 结构

解法是 线性静态 - 单个约束

------------------------------------------------------------

警告

Scenario 名称开始从 "1"

该名称也许对一些分析解算器是一个无效的名称。

下列开始字符可能无效：!@#$*&^=|`',~:{([])}-_.0123456789

操作：重新命名文件。


------------------------------------------------------------


Mesh-Based Errors Summary
-------------------------

Total: 0 error and 0 warning


Material-Based Errors Summary
-----------------------------

Total: 0 error and 0 warning


Solution-Based Errors Summary
-----------------------------

Total: 0 error and 0 warning


Load/BC-Based Errors Summary
----------------------------

警告
Constraint "Fixed(1)" is applied to a mesh that has a face affected by tiny features.
(highlighted).
The geometric constraint may not be distributed completely. Use the expanded display
style of the constraint to verify. Meshing the highlighted geometry again may correct
this condition.

警告
Load "Force(1)" is applied to a mesh that has a face affected by tiny features.
(highlighted).
The geometric load may not be distributed completely. Use the expanded display style of
the load to verify. Meshing the highlighted geometry again may correct this condition.

Total: 0 error and 2 warnings


Nastran Model Check Completed
============================================================
列出信息创建者：     gyf
日期                           ： 2009-4-17 12:52:12
当前工作部件              ： E:\ug\12_sim1.sim
节点名                      ： rd-gyf
============================================================


*** 12:52:16 ***
Starting Nastran Exporter

*** 12:52:16 ***
Writing Nastran System section

*** 12:52:16 ***
Writing File Management section

*** 12:52:16 ***
Writing Executive Control section

*** 12:52:16 ***
Writing Case Control section

*** 12:52:16 ***
Writing Bulk Data section

*** 12:52:16 ***
Writing Nodes

*** 12:52:17 ***
Writing Elements

*** 12:52:17 ***
Writing Physical Properties

*** 12:52:17 ***
Writing Materials

*** 12:52:17 ***
INFORMATION : Reference temperature for material STEEL has been set to the
              solution's default temperature

*** 12:52:17 ***
Writing Loads and Constraints

*** 12:52:17 ***
Writing Coordinate Systems

*** 12:52:17 ***
Summary of Bulk Data cards written

+----------+----------+
|   NAME   |  NUMBER  |
+----------+----------+
| CTETRA   | 609      |
| FORCE    | 50       |
| GRID     | 1224     |
| MAT1     | 1        |
| MATT1    | 1        |
| PARAM    | 6        |
| PSOLID   | 1        |
| SPC      | 73       |
| TABLEM1  | 3        |
+----------+----------+

*** 12:52:17 ***
Nastran Deck Successfully Written
上面是分析检查出来的结果，大家帮忙看看是怎么回事，谢谢了。

jxthyunfeng

文件命名为1怎么会无效了。不解

yueyaba

检查一下 .f04  .f06文件，看看是否有fatal error 等

jxthyunfeng

这是我的这几个文件,帮忙看看

jxthyunfeng

有没哪位知道的，说下好吗