装配的问题，帮帮我！

aeli

图1，两个零件装配，其中零件2为多配置零件（几个配置主要是斜面角度的不同），零件2与零件1的配合要求为斜面与立柱面重合（零件2选配置1），装配好以后，作线性阵列，阵列好的实体分别选2、3、4的配置，本以为会是图2的结果，出来的却是图3的形状，问题出在什么地方？不能用配置中变化的面作约束吗？谢啦！<img src="attachments/dvbbs/2004-3/200432610301851635.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/2004-3/200432610301851635.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

aeli

图2<img src="attachments/dvbbs/2004-3/200432610341791357.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/2004-3/200432610341791357.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

aeli

图3<img src="attachments/dvbbs/2004-3/200432610361290826.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/2004-3/200432610361290826.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

jeeryshi

这样呀！还是不太明白呀！

aeli

我的意思是阵列的源零件它的装配关系是斜面与立柱面重合，可是做了阵列以后，把阵列的零件分别选用不同的配置后，斜面与立柱重合的配合关系不对了，如图3所示。什么原因呢？

aeli

唉，没人愿意回答我的问题吗？

jeeryshi

难到点了竖的那个面再点斜面加上重合没有用吗？是不是你的软件有问题呀！我做一个看看！

jeeryshi

这个是不是呀！先把侧面重合，在配合对齐中选同向对齐，然后再反斜面和竖的那面对上就可以了！
<img src="attachments/dvbbs/2004-3/20043278275018378.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/2004-3/20043278275018378.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

[此贴子已经被作者于2004-3-27 8:28:29编辑过]

smltiger

以下是引用aeli在2004-3-26 21:13:09的发言：
唉，没人愿意回答我的问题吗？

能否part發上來 大夥幫你看看
沒人回答原因 可能是
1.不懂你說什麼
2.因沒實驗過 又懶的動手 各忙各的事