如何才能產生行號?

student6

<p>如何才能產生行號?如下N1N2是要改後處理器嗎?還是有哪個地方需要設定?%<br/>N1G90G21G0G17G40G49G80<br/>N2G91G28Z0<br/>N3/G5.1Q0(AICC)<br/>N4/G5.1Q1(AICC)<br/>N5M6T<br/>N6(NC Start)<br/>N7(CUTTER:T0D10.R0S0.H150.)<br/>N8(Flat: 10.D)<br/>N9G90G54X0Y0<br/>N10G00G43Z10.H03<br/>N11S3000M03<br/>N12G00X46.856Y37.249<br/>N13G00Z5.<br/>N14M08<br/>N15G01Z-.007F500<br/>N16X27.418Y23.631F1000<br/>N17X27.181Y23.362</p><p>謝謝!</p>

liyonghua

<p>改后处理器</p>

student6

<div class="msgheader">QUOTE:</div><div class="msgborder"><b>以下是引用<i>liyonghua</i>在2006-11-2 15:03:00的发言：</b><br/><p>改后处理器</p></div><p>可以告知如何改嗎?? </p><p>謝謝!</p>

同期

改后处理器

yjhcj

1、是否需要N行号？ <br/>&nbsp; &nbsp; &nbsp; &nbsp; % <br/>&nbsp; &nbsp; &nbsp; &nbsp; :0001 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N10G28G91X0Y0Z0 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N30T1M6 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N40G0G90X-25.Y-40.S800 M3 <br/>&nbsp; &nbsp; <br/>如这上面的N10、N30、N40，另外行号的起始、增量、最大都可以定义。如果不想要行号，可修改为以下值： <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; define format ( N ) <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; not permanent <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; end define

东东123456

<p>&nbsp;&nbsp; 红色部分</p><p>message output&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = false<br/>&nbsp;&nbsp; block order&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = true<br/>&nbsp;&nbsp; use hole top in cycles = true<br/>&nbsp;&nbsp; integer 12&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = 0<br/>&nbsp;&nbsp; integer 51&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = 6<br/>&nbsp;&nbsp; integer 69&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = 2<br/>&nbsp;&nbsp; integer 9&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = 0<br/>&nbsp;&nbsp;<font color="#e6421a"> block start&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; = 1 <br/>&nbsp;&nbsp; block increment&nbsp; = 1<br/></font>#123<br/>&nbsp;<font color="#e6421a">define block tape start</font></p><p><br/><font color="#e6421a">end define</font></p><p>&nbsp;</p>

[此贴子已经被作者于2007-1-23 17:04:43编辑过]

student6

<div class="msgheader">QUOTE:</div><div class="msgborder"><b>以下是引用<i>yjhcj</i>在2007-1-23 8:46:00的发言：</b><br/>1、是否需要N行号？ <br/>&nbsp; &nbsp; &nbsp; &nbsp; % <br/>&nbsp; &nbsp; &nbsp; &nbsp; :0001 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N10G28G91X0Y0Z0 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N30T1M6 <br/>&nbsp; &nbsp; &nbsp; &nbsp; N40G0G90X-25.Y-40.S800 M3 <br/>&nbsp; &nbsp; <br/>如这上面的N10、N30、N40，另外行号的起始、增量、最大都可以定义。如果不想要行号，可修改为以下值： <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; define format ( N ) <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; not permanent <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; end define </div><p>你好: </p><p>大概你誤會我的意思了,我現在轉出來的程式都沒有行號,我想讓他有行號,該怎麼改呢?這樣要找比較好找 </p><p>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 謝謝</p>

piterli

<p>define format ( N ) <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; not permanent <br/>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; end define </p><p>去掉not就可以了,一定会有行号,但行号的起始、增量、最大都要另外定义</p>