来一个画长圆孔的lsp(外国人设计的图纸基本上都是长孔)

lovehaer

(defun c:loc()<br/>&nbsp;&nbsp;&nbsp; (setq os (getvar "osmode"))<br/>&nbsp;&nbsp;&nbsp; (setvar "osmode" os)<br/>&nbsp;&nbsp;&nbsp; (setq pot (getpoint "\n请输入插入点&lt;退出&gt;："))<br/>&nbsp;&nbsp;&nbsp; (setq pot1 (getpoint "\n请输入插入点&lt;退出&gt;："))<br/>&nbsp;&nbsp;&nbsp; (setq md1 (getreal "\n请输入直径:"))<br/>&nbsp;&nbsp;&nbsp; (setvar "osmode" 0)<br/>&nbsp;&nbsp;&nbsp; (setq md (/ md1 2))<br/>&nbsp;&nbsp;&nbsp; (setq ang (/ pi 2))<br/>&nbsp;&nbsp;&nbsp; (setq ang1 (angle pot pot1))<br/>&nbsp;&nbsp;&nbsp; (setq pot2 (polar pot (+ ang1 ang) md))<br/>&nbsp;&nbsp;&nbsp; (setq pot3 (polar pot (- ang1 ang) md))&nbsp; <br/>&nbsp;&nbsp;&nbsp; (setq pot4 (polar pot1 (+ ang1 ang) md))<br/>&nbsp;&nbsp;&nbsp; (setq pot5 (polar pot1 (- ang1 ang) md)) <br/>&nbsp;&nbsp;&nbsp; (setq pot6 (polar pot (+ ang1 ang) (* md 1.2)))<br/>&nbsp;&nbsp;&nbsp; (setq pot7 (polar pot (- ang1 ang) (* md 1.2)))&nbsp; <br/>&nbsp;&nbsp;&nbsp; (setq pot8 (polar pot1 (+ ang1 ang) (* md 1.2)))<br/>&nbsp;&nbsp;&nbsp; (setq pot9 (polar pot1 (- ang1 ang) (* md 1.2)))<br/>&nbsp;&nbsp;&nbsp; (setq pot10 (polar pot (+ ang1 pi) (* md 1.2)))<br/>&nbsp;&nbsp;&nbsp; (setq pot11 (polar pot1 ang1 (* md 1.2)))<br/>&nbsp;&nbsp;&nbsp; (command "arc" "c" pot pot2 pot3)<br/>&nbsp;&nbsp;&nbsp; (command "arc" "c" pot1 pot5 pot4)<br/>&nbsp;&nbsp;&nbsp; (command "line" pot2 pot4 "")<br/>&nbsp;&nbsp;&nbsp; (command "line" pot3 pot5 "")<br/>&nbsp;&nbsp;&nbsp; (command "line" pot6 pot7 "")<br/>&nbsp;&nbsp;&nbsp; (command "line" pot8 pot9 "")<br/>&nbsp;&nbsp;&nbsp; (command "line" pot10 pot11 "")<br/>&nbsp;&nbsp;&nbsp; (setvar "osmode" os)<br/>&nbsp;&nbsp;&nbsp; (princ)<br/>&nbsp; )

xfyy

<p>看看</p>

前生

<p>加上长孔倾斜时的功能吧!</p>

pwints1

(defun c:loc()
    (setq os (getvar "osmode"))
    (setvar "osmode" os)
  (command "layer" "m" "中心线" "c" "red" "" "l" "center" "" "")
  (command "layer" "m" "粗实线" "c" "t" "0,255,255" "" "lw" "0.35" "" "")
    (setq pot (getpoint "\n请输入插入点<退出>："))
    (setq pot1 (getpoint pot "\n请输入插入点<退出>："))
    (setq md1 (getreal "\n请输入直径:"))
    (setvar "osmode" 0)
    (setq md (/ md1 2))
    (setq ang (/ pi 2))
    (setq ang1 (angle pot pot1))
    (setq pot2 (polar pot (+ ang1 ang) md))
    (setq pot3 (polar pot (- ang1 ang) md))  
    (setq pot4 (polar pot1 (+ ang1 ang) md))
    (setq pot5 (polar pot1 (- ang1 ang) md))
    (setq pot6 (polar pot (+ ang1 ang) (* md 1.2)))
    (setq pot7 (polar pot (- ang1 ang) (* md 1.2)))  
    (setq pot8 (polar pot1 (+ ang1 ang) (* md 1.2)))
    (setq pot9 (polar pot1 (- ang1 ang) (* md 1.2)))
    (setq pot10 (polar pot (+ ang1 pi) (* md 1.2)))
    (setq pot11 (polar pot1 ang1 (* md 1.2)))
    (setvar "clayer" "粗实线")
    (command "arc" "c" pot pot2 pot3)
    (command "arc" "c" pot1 pot5 pot4)
    (command "line" pot2 pot4 "")
    (command "line" pot3 pot5 "")
    (setvar "clayer" "中心线")
    (command "line" pot6 pot7 "")
    (command "line" pot8 pot9 "")
    (command "line" pot10 pot11 "")
    (setvar "osmode" os)
    (princ)
  )

一路风情

高啊
高啊高啊高啊高啊高啊高啊高啊

mmmoving

看不懂啊～～～～～～～

cam027

(defun c:ccs(/ os a b d ang p1 aa p2 p3 bb p4 p5 p6)
  (setq os (getvar "osmode"))
  (setvar "osmode" 0)
  (setq a (getdist "\n 输入腰孔的长度:"))
  (setq b (getdist "\n 输入腰孔的宽度:"))
  (setq d (- a b))
  (setq ang (getangle "\n 输入旋转角度:"))
  (setq p1 (getpoint "\n 输入腰孔的中心点："))
  (setq aa (/ d 2.0) p2 (polar p1 0 aa) p3 (polar p1 pi aa) bb (/ b 2.0))
  (setq p4 (polar p3 (* pi 1.5) bb) p5 (polar p2 (* pi 1.5) bb) p6 (polar p3 (* pi 0.5) bb))
  (command "pline" p4 "w" "0" "0" p5 "a" "ce" p2 "a" "180" "l" p6 "a" "ce" p3 "a" "180" "l" "")
  (command "rotate" "l" "" p1 (* (/ 180 pi) ang))
  (setvar "osmode" os)
(princ)
)

abcdefg1234567

嗯，哦。。。。。。。
说实话。。。
没看明白。。。。。。