[求助]哪位高手知道啊，小弟安装3.0,服务器出错?

dercheng

<p>1.start pro/e setup<br/>開始安裝</p><p><br/>2.open ptc_licfile.dat with your fav txt-editor<br/>使用你最常用的文字編輯器&nbsp; 打開ptc_licfile.dat</p><p><br/>3.replace every occurance of &lt;HOSTID&gt; with the one shown in the bottom left corner of the Pro/e setup<br/>&nbsp;(its your mac-id, format: xx-xx-xx-xx-xx)<br/>把你的 網路卡序號打在每一個 &lt;HOSTID&gt;位。(可使用搜尋及取代功能)&nbsp;&nbsp; </p><p>例如：HOSTID=PTC_HOSTID=&lt;HOSTID&gt;<br/>改成：HOSTID=PTC_HOSTID=00-13-CE-4C-21-79</p><p><br/>4.安裝PROE </p><p>.install pro/e - pro/m - pro/ds, i dont care which one or in which order<br/>.on license-config screen select "nodelocked license" and point to edited ptc_licfile.dat<br/>.blalala install</p><p><br/>5.next for pro/engineer:(以下為針對pro/engineer模組之破解)<br/>a) (if u didnt install the complete package, u get "missing file" errors, accept or bleed)<br/>&nbsp;&nbsp; (如果有些模組沒安裝, 破解時會出現檔案找不到訊息)</p><p>b) run ptc.pro engineer.wildfire.3.0.m060-patch.exe, point to &lt;installdir&gt;\i486_nt\obj folder<br/>　 將SHooTERS\ptc.pro engineer.wildfire.3.0.m060-patch.exe複製到&lt;安裝路徑&gt;\i486_nt\obj下並執行。</p><p>c) edit &lt;pro/e installdir&gt;\bin\proev.bat<br/>&nbsp;&nbsp; 以文字編輯器編輯&lt;pro/e安裝路徑&gt;\bin\proev.bat</p><p>e) change "%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr%" in<br/>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; "%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr% PTC_KEY=0"<br/>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; (add PTC_KEY=0)<br/>&nbsp;&nbsp; 將第2行" "內的字串複製起來，將&lt;pro/e安裝路徑&gt;\bin\proev.bat內如第1行" "內的字串替換。</p><p><br/>6.pro/mechanica:(以下為針對pro/mechanica模組之破解)<br/>.point to &lt;pro/m installdir&gt;\i486_nt\bin<br/>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &lt;pro/m installdir&gt;\i486_nt\obj<br/>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &lt;pro/m installdir&gt;\i486_nt\ptc<br/>&nbsp;&nbsp; 將SHooTERS\ptc.pro mechanica.wildfire.3.0.m060-patch.exe複製到&lt;安裝路徑&gt;\i486_nt\obj並執行<br/>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &lt;安裝路徑&gt;\i486_nt\ptc並執行</p><p><br/>7.pro/distributed services:(以下為針對pro/distributed services模組之破解)<br/>.run ptc.distributed.services.m060-patch.exe and point to &lt;pro/ds installdir&gt;\i486_nt\obj</p><p>將SHooTERS\ptc.distributed.services.m060-patch.exe複製到&lt;安裝路徑&gt;\i486_nt\obj並執行</p><p><br/>重要：6、7項為針對有安裝此模組時，才需要作此部份之破，否則只需破解pro/engineer模組即可。</p><p>8.大功告成。<br/></p>

uncal22

谢谢楼上的.你的热心我非常感谢.但是我的错因是BOTEBOOK上提示未找到符合本机的服务器行.我想应该不是安装的问题而是软件的问题,目前为止我还找不到原因!

xuer1122

<p>２楼说得太复杂了，其时很简单滴</p>

yaohui616

<p>２楼说简单点</p><p></p>